Coming soon Power Management IP · 22nm ULL

SIMO DC/DC converter

Dolphin Semiconductor’s next-generation 3-output Single Inductor Multiple Output (SIMO) DC/DC buck converter in 22nm ULL. One external inductor powers three independent SoC domains, cutting BOM, board area and battery current.

up to −52%PCB footprint
up to −38%BOM cost
50% → 69%system efficiency

3 configurable outputs 1 × 1 µH inductor 3 × 4.7 µF output caps Ultra-low Iq Low ripple

Early access to the datasheet and priority evaluation slots. Questions about your SoC? Talk to our power-management team.

Illustrative mixed-signal SoC layout

Key features

  • Multi-rail efficiency: 3 independently configurable, high-efficiency outputs
  • BOM optimized: a compact 1 µH inductor and small 4.7 µF output capacitors reduce solution size, cost and design complexity
  • Ultra-low power: very low quiescent current
  • Low noise: very low output ripple

Applications

  • BLE and BLE MCUs
  • MCUs: general purpose, high-performance, low-power
  • GNSS: low-power, high-performance

Example of SIMO integration in a BLE MCU

The SIMO converter sits on-chip and, utilizing just one inductor, generates the RF, memory, digital-core and AON supply rails. Compared to the traditional solution based on a standard DC/DC buck converter and a number of LDOs, this solution offers higher efficiency, reduced footprint and BOM cost.

BLE MCU SoC Supply+Coin cellor 2 × AAor 3.3 V rail LDO 1.8 VI/OGPIO, serial interfaces SIMODC/DC converter3 outputs · 1 inductor1.1 V0.6 V0.8 V LDO 0.9 VLDO 0.8 VBLE radio (RF)TX/RX, synthesizerMemorySRAM Digital coreCPU, logic, peripheralsAlways-on domainRTC, wake-up, retention 1 µH 3 × 4.7 µF Off-chip: 1 inductor + 3 capacitors
Dolphin SIMO DC/DC IPLDO regulatorsSoC power domains

Efficiency gains for GP MCU, BLE MCU and GNSS

Replacing a buck + LDO chain with SIMO-generated rails removes most of the linear-regulation losses. The result is lower battery current in both normal and low-power modes.

Conventional

System efficiency: 50%

3.3 VBUCK1.1 VLDO0.9 VLDO0.8 VLDO0.6 VLDO0.8 VLDO1.8 VRF8 mASRAM5 mALOGIC30 mAAON10 µAI/O1 mA

SIMO Config. 1

System efficiency: 69%

3.3 VSIMO1.1 V0.8 V0.6 VLDO0.9 VLDO0.8 VLDO1.8 VRF8 mASRAM5 mALOGIC30 mAAON10 µAI/O1 mA

SIMO Config. 2

System efficiency: 66%

3.3 VSIMO1.1 V0.6 V0.8 VLDO0.9 VLDO0.8 VLDO1.8 VRF8 mASRAM5 mALOGIC30 mAAON10 µAI/O1 mA
ConventionalSIMO Config. 1SIMO Config. 2
Battery current17.4 mA12.5 mA13 mA
Efficiency in normal mode49.8 %68.8 %66.2 %
Efficiency in low-power mode22 %22 %65 %

In Config. 1 the always-on domain stays on an LDO, so low-power efficiency is the same as the conventional tree (22%). Config. 2 powers the always-on domain from the SIMO and reaches 65% in low-power mode. Figures for the load currents shown: RF 8 mA, SRAM 5 mA, logic 30 mA, AON 10 µA, I/O 1 mA.

Total cost of ownership benefits

Integrating the SIMO converter on-chip reduces board area, external components and overall system cost compared with multiple integrated bucks or an external SIMO PMIC.

SIMO (integrated) vs SIMO (PMIC)

Integration removes the external PMIC and its routing, and allows a smaller inductor and smaller capacitors.

SIMO (PMIC)PMIC + 5 external partsSoCPMICSIMO (integrated)5 external partsSoCpower area
−70%PCB footprint
−86%BOM cost
−81%TCO

Illustrative board layouts. Figures are “up to” values.

BenefitSIMO (integrated) vs 3× DC/DC (integrated)SIMO (integrated) vs SIMO (PMIC)
PCB footprint reductionup to 52%
up to 70%
BOM cost reductionup to 38%
up to 86%
TCO reductionup to 31%
up to 81%

Join the SIMO DC/DC converter waitlist

The SIMO DC/DC converter IP is not yet available. Join the waitlist to be among the first to evaluate it:

  • Early access to the datasheet
  • A priority evaluation slot for your SoC project
  • A technical call with our power-management team

A question about your SoC? Talk to our power-management team.

Join the SIMO DC/DC converter waitlist

© 2024 Copyright by Dolphin Semiconductor – All Rights Reserved